Two Batteries, Two Ports, One Fixed Charger: A Switching Cable for a Robotic Vehicle

This robotic vehicle has two things that need charging and they do not share a connector. One is the battery inside the machine, charged through a socket in its front recess. The other is an external pack, charged on its own terminals. The charger is installed at a fixed position in the bay.

The requirement was blunt: the machine is not to be moved to charge, and the crew is not to be handed two chargers to keep track of. Two batteries, two ports, zero repositioning.

Robot vehicle charging station: wall-mounted charger with XLR cable, 24 V 30 Ah battery pack on the tool cabinet, and the XLR-to-SAE switching cable connected to the vehicle
Set-up: the charger is mounted on the wall, the 24 V 30 Ah pack sits on the cabinet, and the switching cable runs from the ring terminals to the machine's front socket. Annotations mark the SAE-to-ring-terminal end, the XLR male-to-female joint and the XLR-female-to-SAE end at the vehicle.

The set-up: one charger, two charging points, different connectors

The machine’s own battery is charged through a recessed circular multi-pin socket — an XLR-type connector set into the front panel, beside the control knob. It is small, it sits inside a recess, and it is not a terminal anyone wants to reach with a spanner.

The external pack is a different animal. It terminates on studs, and the only thing that stays tight on a stud is a ring lug. The sketch that came with the machine draws that end as SAE to ring terminal: a ring terminal on the pack, an SAE connector a hand’s length away.

Two connector families, two locations, one charger. Between them the same sketch shows the other two parts of the run — an XLR male to female coupling, and an XLR female to SAE lead that lands on the machine’s socket.

The constraint

Three conditions, and the easy answer to any one of them breaks another.

1. The charger does not move. It is installed, wired, and left alone. Whatever the crew needs to reach has to be reachable from where the charger already is.

2. Neither does anything else. The vehicle parks on its mark and stays there while it charges; the pack stays where it is stored. The customer’s own phrasing was that charging happens in a fixed environment and the equipment should not be relocated every time — which rules out walking the machine over to a second charging point.

3. The change had to stay outside the machine. No second socket cut into the body, no changeover relay tapped into the vehicle’s loom. Opening a production machine to add a switch is a modification with a warranty attached to it, and it moves responsibility for the switching from a cable to us.

Our call: put the switching in the cable

A selector switch in the charger, or a relay inside the vehicle, both do the same job on paper: choose which battery gets the charge. Both also introduce a state that has to be got right — a switch left in the wrong position, a contactor that fails closed, two packs tied together at different states of charge.

A cable cannot be in two places at once. If the crew plugs the SAE end onto the pack, the machine is not connected; if they plug the XLR end into the vehicle, the pack is not. The interlock is the connector, and it cannot be left in the wrong position because there is no position to leave it in.

It also gives the crew one action instead of a procedure: nothing to check, nothing to reset, no indicator to read before walking away.

What we built

A set of charging ports on the charger side, and one switching cable that carries the connection to whichever of the two points is being charged.

ItemDetail
ChargerOne unit, installed at the fixed charging position
Battery-side endSAE connector to ring terminals
Vehicle-side endXLR female to SAE
Mid-runXLR male to female coupling
SwitchingManual — by which end is plugged in. No relay, no selector switch
Vehicle modificationNone: no second socket, no tap into the loom
Pack in the sketch24 V / 30 Ah
WarrantyStandard 2-year, extendable on request

The pack drawn on the machine’s reference photo is marked 24 V / 30 Ah, and the vehicle’s charging socket is the recessed XLR that was already on its front panel. Neither of those changed. What was added was the set of ports and the cable that joins them.

Why three transitions instead of one adapter

RunConnectsConnectorWhy that connector
Charger to packCharger lead to the pack studsSAE to ring terminalA ring lug is the termination that stays tight on a stud under vibration; the SAE is the disconnect point
Charger to vehicleCharger lead to the front recess socketXLR female to SAEThe machine’s port is XLR; SAE on the other end lets the same lead serve both charging points
ExtensionTwo cable runsXLR male to femaleJoins the runs so the cable reaches the vehicle from the fixed charger, and comes apart for handling

Each of those is a single-purpose part. The alternative — one universal adapter with three tails — is the part that gets lost, and the part nobody can identify once it has.

The ring-terminal end exists for a second reason. Putting an SAE plug on the pack would mean a pigtail bolted to the studs anyway, and then the crew is handling two connections instead of one every time the pack is charged.

What we did not do

We did not supply two chargers. The brief would have allowed it, and on paper it would also have avoided relocation. It also means two AC feeds, two units to keep alive, and an installation that grows every time another battery is added.

We did not open the vehicle. A second socket in the body, or a relay in the loom, would have made the switching automatic — at the price of modifying a production machine and owning that modification.

We did not design a simultaneous two-battery mode. Charging both at once from one lead means two packs at different states of charge tied together, and current moving between them before either finishes. That is a different design with a different set of protections, and it is not what the bay needed.

Result — and what to send us

Two batteries, two ports, zero repositioning.

The crew no longer moves the machine to charge, and no longer keeps track of which charger is which. One end of the cable is on the pack, or the other end is in the vehicle’s socket; the charger stays where it was installed, and the bay stays a bay.

If your machine has more than one charging point, send us four things: a photo of each connector, the distance from the charger’s position to each one, the pack’s voltage and capacity, and whether the two ever have to charge at the same time. The last question decides the architecture; everything else is a cable.

Every charger we ship carries a standard 2-year warranty, extendable on request. If you are working out how to charge two packs on one machine without adding a second charger or touching the machine’s wiring, send us the two connector photos and we will tell you which end of the run the switching belongs on.

See the battery charger range →

Share:

More Posts

Related Solutions

Send Us A Message

Scroll to Top
Contact VoitaTech sales team for inquiry

Tell Us About Your Project

Share your application and expected quantity — our B2B team will recommend a suitable platform or custom build.

Tell us three specs - we will name the model

Contact VoitaTech sales team for inquiry

Let's have a chat

Get a tailored quotation

Contact Information